Category Archives: Bicycles

Bicycles, Woodworking

Bike Rack Build 3rd and Final – Install

Oh sweet satisfaction. Finally I get to wrap this project up. Things went smoothly, but of course there were some last minute changes to get everything nice and secure.

The first notable change, which I really should have expected, was a serious case of shrinkage. I bought the green doug fir lumber about 3 weeks prior to the install date. Over those week, while carving and staining, the wood shrank noticeably. When I carved out the recesses for the lap joint the two pieces fit together snugly, requiring some gentle tapping to get the pieces set into each other. By the time I was ready to install, the joint had a quarter inch of clearance on all sides.

I was a little disappointed by this at first,  but it was really a blessing in disguise. The shrinkage allowed a little bit of wiggle room to make sure everything got set up nice and level. 

Continue reading Bike Rack Build 3rd and Final – Install →

Bicycles, Design, Woodworking

Bike Rack Build 2 – Finishing

Sanding, sanding, sanding, sanding. So much sanding to take these rough cuts of dimensional lumber down to a finish to be proud of. Moderately proud of, anyways. I’m not going for a high gloss, pristine mirror finish. I’ll be sticking to some simple poly stain to compliment the colors of the ceiling beams in my apartment. A natural color for the drop, and a dark cross beam.

The green doug fir 2x’s that I bought were definitely rough. I started off with my random orbital sander with 80 grit sand paper. After a thorough twice-over with that I moved to 120 grit, then to 220. At this point the wood was nice and smooth, but I was done for the day. The stain would have to wait.

The orbital sander makes quick work of the sanding, but isn’t the best choice when applying the stain. As a last step before the stain I used a sanding block with 240 grit sand paper and went over everything one more time, sanding with the direction of the grain. I doubt I got all of the swirls from the orbital sander out of the wood, but I didn’t notice many by the time I was done.

Continue reading Bike Rack Build 2 – Finishing →

Bicycles, CAD, Carving, Woodworking

Bike Rack Build – Construction

Content with the CAD model I had drawn up I set to work on actually making it. Step one was to find the materials. I was hoping to make this out of red cedar, like I used on my guitar rack, but Lowe’s didn’t carry any 2×12 red cedar. The only thing available in 2×12 was green douglas fir.

Fortunately, this is also about the cheapest option in the store. I picked out an 8 foot length of 2×12 and 2×6, doing my best to find consistent grain and minimal knots, and headed to the shop.

The first step is getting an overall picture of how much wood would need to be trimmed off. I only had about 8″ of extra length on the 2×6, so I didn’t have much choice laying out the hole patterns. However, I did still have some options with orientation and used the opportunity to cut off the worst of the ends.

Continue reading Bike Rack Build – Construction →

Bicycles, CAD, Design, Woodworking

Bike Rack Design

My new apartment has considerably more square footage than my previous place and I can finally bring my bikes inside out of the elements. This is great considering the added moisture in the PNW. However, we need a way to keep them neat and out of the way but still accessible. They can’t stay leaned up against the wall by the door, anymore.

I picked up a few bike racks from Amazon to mount on the wall. However, as has been an issue in a few other posts, the metal stud drywall setup in the new apartment doesn’t hold up to any sort of load. So after quickly installing the bike in drywall and seeing the drywall anchors slowly pull out of the wall I knew I’d have to take a similar approach I took on my guitar rack. 

Step one is to nail down the design. I took some rough measurements and made a couple quick sketches until I could take it to Solidworks. 

Continue reading Bike Rack Design →

Bicycles, Found Materials, Restoration

Found Supplies: Peugeot PR10 Frameset

Recently I was dropping my girlfriend off at work in downtown Portland when I spotted something under an underpass. I circled around after dropping her off and parked to check it out. There was a shopping cart with a couple of bike frames and tires, seemingly abandoned. I looked around the area, spent a few minutes checking out what was in the cart, and no one seemed to have any interest in the bikes.

I am always looking for things like this. A cache of goods might have a treasure in it if you’re looking for the right thing. What caught my eye in this cart was a white Peugeot road bike frame. I spent a few minutes looking it over, and it was in rough shape. 

Remembering that most older Peugeot frames are pretty heavy, cheap steel I almost got back in my car and left. I didn’t need another low priority, low value project. But as I was leaving a sticker on the chrome fork caught my eye. It said “Reynolds 501”. The fork, at least, was worth the trouble.

Continue reading Found Supplies: Peugeot PR10 Frameset →